Fluke 789 Process Meter

 Fluke 789 Process Meter

Fluke 789 loop calibration multimeter has a 24-Volt loop supply reducing the need for taking a separate power supply for offline transmitter testing.

Fluke 789 Process Meter doubles your troubleshooting power and is Fluke Connect-enabled

 

The Fluke 789 ProcessMeter is the ultimate troubleshooting tool for electricians and instrumentation professionals. It combines the functionality of a loop calibrator with the power of a digital multimeter, and the wireless capabilities of Fluke Connect connectivity with optional IR3000FC module. The 789 has a display that's not only twice as large as the Fluke 787B, but also twice as bright with two levels of backlighting. And its built-in, selectable 250 ohm HART® resistor eliminates the need to carry a separate resistor.

 

The 789 also has a 24-Volt loop supply, which reduces the need to carry a separate power supply when doing offline transmitter testing. You can add an optional temperature measurement module and the wireless data logging capabilities of the Fluke Connect™ mobile app to log data wirelessly to your smart phone and review it from a remote location. So now process technicians can do a lot more while carrying a lot less.

 

Other useful features:

 

- Includes 0% and 100% buttons to toggle between 4 and 20 mA sourcing for a quick span check

- Provides all standard DMM capabilities including frequency measurement to 20 kHz, Min/Max/Average/Hold/Relative modes,and diode test and continuity beeper

- Simultaneous displays mA and % of scale readings

- Provides 20 mA DC current source/loop calibrator/simulator

- Offers manual step (100%, 25%, Coarse, Fine) plus auto step and auto ramp

- Delivers 0.1% dc voltage accuracy and 0.05% dc current accuracy

- Provides 1200 ohm drive capability on mA source

- Offers HART mode setting with loop power and a built-in 250 ohm resistor

- Offers externally accessible fuses and batteries for easy replacement

 

Fluke 9132 - 9133 Portable Infrared Calibrator

 Fluke 9132 - 9133 Portable Infrared Calibrator

Precision when you need it for infrared temperature calibration

 

- Certify IR pyrometers from –30 °C to 500 °C (–22 °F to 932 °F)

- Large 57 mm (2.25 in) blackbody target

- RTD reference well for contact temperature measurement

- Small, compact design

 

Whether you’re using in-line or handheld infrared pyrometers, you need good calibration standards to verify their accuracy. Our portable IR calibrators provide stable blackbody targets for calibrating noncontact IR thermometers from –30 °C to 500 °C.

 

These units feature a temperature controlled measurement surface with a diameter of 2.25" (57 mm). The target temperature can be controlled in set-point increments of 0.1 ° from –30 °C to 500 °C and a well is located directly behind the blackbody surface for contact calibration.

infrared Calibrator

9132

 

For IR calibrations above normal ambient, the 9132 provides a stable measurement surface up to 500 °C (932 °F). Short heating and cooling times mean you won't have to wait long to get your work done.

 

9133

 

If you're calibrating IR guns at cold temperatures, you'll love our new 9133. With solid-state cooling technology, this new IR calibrator reaches –30 °C (22 °F) in normal ambient conditions. With a conveniently located dry gas fitting on the front bezel, ice build up on the target can be avoided. At the upper end of its range, the 9133 provides stable temperatures to 160 °C (320 °F).

 

With heating and cooling times of about 15 minutes from ambient to either extreme, the 9133 gets you to temperature quickly and performs when it gets there.

Fluke 773 Milliamp Process Clamp Meter

Fluke 773 Milliamp Process Clamp Meter saves time and money by measuring output signals without shutting down the system

The Fluke 773 milliamp clamp meter is accurate and versatile. It saves time and money by measuring 4–20 mA signals five times faster than with traditional DMMs, and without breaking the loop. That means you can troubleshoot a live device without having to power down and possibly miss something going on in the process.

Milliamp Process Clamp Meter  

The 773 is ideal for troubleshooting transmitters, valves, and programmable logic controllers (PLCs) found in process plants. It measures low level dc current and correlates process indication with a real physical value. And it measures up to 99.0 mA non-contact, including 10 to 50 mA signals in older control systems.

The 773 also sources and measures dc voltage, so it can be used to troubleshoot voltage input and output devices. You can detach the clamp section of the meter and use it as a remote jaw, connected to the main body by an extension cable to make it easier to take measurements in tight spaces. Plus, automatic power-off features save battery life so you can work longer without changing the batteries.

Other useful features:

• Sources DC voltage to test input devices that accept a 1-5V or 0 to 10V signal
• Simultaneously measures the mA signal with the clamp and sources a mA signal
• Measures mA signals for PLC and control system analog I/O
• Simulates 4-20 mA signals for testing control system I/O
• Features a detachable clamp with extension cable for measurements in tight locations
• Extends battery life with auto-off and backlight timeout
• Captures and displays changing measurements with Hold function
• Measures 4 to 20 mA signals with in-circuit measurement
• Includes simultaneous mA in-circuit measurement with 24V loop power for powering and testing transmitters
• Offers mA or voltage output linear ramp or 25% step output
• Provides scaled mA output to provide a continuous mA signal that corresponds to the 4 to 20 mA signal measured by the mA clamp
• Enables milliamp signal logging to a separate logging device without breaking the loop
• Applies a mA input signal to a device and measure its’ 4-20 mA output on devices such as valves or mA isolators
• Dual backlit display with both mA measurement and percent of 4 to 20 mA span
• Measurement Spotlight to illuminate hard to see wires in dark enclosure
• Measures 10 to 50 mA signals in older control systems using the 99.9 mA range
• Automatically changes the 4 to 20 mA output for remote testing

R&S SMB100A Microwave Signal Generator

R&S SMB100A Microwave Signal Generator

The compact, versatile R&S®SMB100A microwave signal generator with a frequency range up to 40 GHz provides outstanding spectral purity and high output power. In addition, it features easy operation, comprehensive functionality and low cost of ownership.

R&S SMB100A Microwave Signal Generator

For even higher frequencies, the frequency range of the R&S®SMB100A can be easily extended with the R&S®SMZ frequency multiplier. The R&S®SMB100A plus R&S®SMZ solution combines easy handling with precise, adjustable output levels in the frequency range from 50 GHz to 110 GHz (adjustable output levels are not possible with R&S®SMZ170).

Key facts:

- Wide frequency range from 100 kHz to 40 GHz

- Excellent signal characteristics with low SSB phase noise of typ. –128 dBc (at 1 GHz, 20 kHz offset)

- High output power of up to +27 dBm (meas.)

- All important analog modulations with AM, FM/φM and pulse modulation supported

- Compact size with only two height units and low weight

Fluke 724 Temperature Calibrator

Fluke 724 Temperature Calibrator

Fluke 724 Temperature Calibrator The Fluke 724 is powerful yet easy-to-use temperature calibrator that sources and measures 10 thermocouple types, and 7 RTD types, plus volts and ohms. It also measures mA while supplying loop power

Temperature Calibrator

Key features:

• A powerful, easy-to-use calibrator that measures and sources functions to test and calibrate most temperature instruments
• Displays input and output simultaneously on the easy-to-read dual display
• Measures RTDs, thermocouples, ohms, and volts to test sensors and transmitters
• Source/simulates thermocouples, RTDs, volts, and ohms to calibrate transmitters

R&S ZVL Vector Network Analyzers

R&S ZVL Vector Network Analyzers

The R&S®ZVL is a cost-efficient, powerful, and portable network analyzer in the compact class, and is therefore ideal for use in development, production, and service. It is the only instrument to combine the functions of a network analyzer, spectrum analyzer, and power meter in a single box, and will thus tremendously increase your work efficiency.

Vector Network Analyzers

Key facts:

- Optional spectrum analysis and digital communications standards

- Bidirectional test set for displaying all four S-parameters

- R&S®ZVL3-75: 75 Ω vector network analyzer for TV and CATV measurements

- Multitrace display for displaying all relevant parameters

- Distance-to-fault measurement for detecting cable faults

- Time domain analysis

- USB connector for R&S®NRP-Z power sensor series for precise power measurements

- Internal battery and 12 V DC operation

- Small, compact, lightweight and portable

Fluke 5650 Type R and Type S Thermocouple Standards

Fluke 5650 Type R and Type S Thermocouple Standards

Made from the finest platinum and platinum-rhodium alloy, these type R thermocouples and type S thermocouples cover a temperature range of 0 °C to 1450 °C with uncertainties as good as 0.15 °C over most of that range. With four different models for each type, we have the type R thermocouple and type S thermocouple to fit your application.

type r thermocouple

Eight models to fit any type R or S thermocouple application:

- Designed by the Fluke Calibration primary temperature standards design team

- Two sizes available, each with or without reference junction

- Uncalibrated accuracy is the greater of ±0.6°C or ±0.1% of reading