Fluke 368 FC & 369 FC Leakage Current Clamp Meters

Fluke 368 FC & 369 FC Leakage Current Clamp Meters

The Fluke 369 FC true-rms leakage current clamp meter helps users detect, document, record and compare leakage current readings over time as a means of preventing unplanned downtime, and identifying intermittent GFCI and RCD trips, all without taking equipment off line.

 The Fluke 369 FC has an oversize 61 mm jaw for work with extra-large conductors. The clamp’s jaw is fully shielded to accurately capture very small leakage signals, and to minimize external electromagnetic interference.

Leakage Clamp Meters

The 369 FC also offers wireless data connectivity via Fluke Connect. As part of Fluke Connect — the industry’s largest system of software and more than 40 wireless test tools — the 369 FC allows you to track changes in leakage current over time, helping to identify potential problems before they turn into major failures

Key features:

- True-rms measurements for accuracy when measuring complex, non-sinusoidal waveforms
- 61 mm jaw opening
- Highest resolution of 1 μA, measure up to 60 A
- Selectable filter function removes unwanted noise
- Max/Min/Average readings and hold function
- Forward-facing LED worklight for use in dark wiring cabinets
- Backlit display; auto backlight off and auto power off for extended battery life
- CAT III 600V safety rating

Fluke Calibration 2700G Series Reference Pressure Gauges

Fluke Calibration 2700G Series Reference Pressure Gauges

The 2700G has an easy-to-use interface that allows you to configure the sampling rate, tare value, damping, and auto-off time interval as well as reset the min/max pressure. You can also view the remaining battery life. Select from 21 different standard engineering units, including bar, in H2O, kPa, MPa, and psi. In addition, the supervisor menu can be used to set one custom engineering unit. To ensure against incorrect measurements, each of the above functions can be locked from use through the supervisor menu.

The 2700G Reference Pressure Gauge can be combined with the Fluke Calibration P5500 series of comparison test pumps to make a complete pressure calibration system. The unique test port design of the P5500 series allows for hand tight connection of the 2700G without the use of PTFE tape.

Fluke 2700G Introduction and Demonstration Video

Feautres:

• Precision pressure measurement from 100 KPa [15 psi] to 70  MPa [10 000 psi]
• Accuracy to 0.02% of full scale
• Easy-to-use, rugged construction for reliable performance
• Combine with the 700PTPK or 700HTPK pump kits for a complete poratble pressure testing solution for up to  Mpa [600 psi] with the PTP-1 pneumatic pump and up to 70 Mpa [10 000 psi]   with the HTP-2 hydraulic pump.
• Combine with the P5510, P5513, P5514, or P5515 Comparison Test Pump for a complete bench top  pressure calibration   solution.
• Test port is 1/ NPT Male, 1/ BSP and M20 X 1.5 adaptors are  included standard.
• USB communications cable and universal power.

Also Read digital pressure gauges

TDMS Test and Data Management Software

TDMS Test and Data Management Software

 

TDMS is a powerful software package providing data management for acceptance and maintenance testing activities. Electrical apparatus data and test results are saved in the TDMS database for historical results analysis.

 

TDMS software organizes test data and results for the majority of electrical apparatus tested with ISA test sets and related software.

 

The TDMS software platform allows the user to select  easily and quickly the most appropriate software package for the required application.TDMS test software uses an open architecture easily expandable with additional software modules at any time.

 

The TDMS Package can be used to test any protective relays in:

 

- Power Generation Plants  

- Distribution network.   

- Transmission network.   

-  Industries.

TDMS software is also a powerful database. It allows to create an electrical network with substations, feeders and the majority of electrical apparatus, such as:

 

- Protective Relays

- Instrument transformers

- Power transformers

- Circuit Breakers

- Energy Meters

- Transducers

- Power Quality Meters

- Ground Grids

- Batteries

For More Details Visit: 

Impulse Surge Tester 7720

Impulse Surge Tester 7720

Coils are used in a wide range of applications e.g. transformer, motor, generator, ignition coil for cars and motorcycles, relay, electromagnet, filter and various inductors, nearly all the electronic and electrical products have to use coils. However, coils do not have a complete automatic manufacturing process like standard electronic components, and the existing enameled wires are neither fault-free during production nor ensure 100% quality guarantee. 

 

7720 is a 8-channel 5KV impulse winding tester that provides the comparison of waveform functions e.g. Area under curve ratio, Area size ratio, Voltage time difference, and you can use the cursor to select desired comparison range to cover all the waveform differences created by electrical properties then detect a faulty component. This model offers various harmonics mode and accommodate all kinds of coils, and become the best tester that you are able to find on the market to certify coil quality.

Please Visit Demo Video

Features:

- Lowe power pulses test function

- Low power non-destructive test analysis

- Automatic Level Control Function (ALC) 

- Waveform learning comparison to achieve rapid test speed

- 8 channels test (7720)

- Multiple winding test function

- Interchangeable between Chinese and English operational   interfaces

- Provide statistic and print functions

Also Read Impulse Winding Tester

Fluke Calibration 5080A High Compliance Multi-Product Calibrator

Fluke Calibration 5080A High Compliance Multi-Product Calibrator

Fluke 5080A Multi-Product Calibrator calibrates your analog workload accurately and reliably, thanks to its high voltage and current compliance. With maximum burden up to 800 mA for ac/dc voltage, and voltage up to 50 V for ac/dc current, 5080A calibrators can drive a wide range of analog meters.

Accurate, reliable analog meter calibration

The 5080A Multi-Product Calibrator calibrates your analog workload accurately and reliably, thanks to its high voltage and current compliance. With maximum burden up to 800 mA for ac/dc voltage, and voltage up to 50 V for ac/dc current, 5080A calibrators can drive a wide range of analog meters.

Options and accessories expand workload coverage

Options and accessories enable you to use the 5080A Multi-Product Calibrator to calibrate an even broader workload, including:

Clamp meters. The 9100-200 10/50 turn coil and 5500A/COIL 50-turn current coil enables the 5080A to calibrate most popular clamp meters at currents up to 1000 A rms amps.

Oscilloscopes. Oscilloscope calibration to 200 MHz quickly, easily, and cost effectively. Verify dynamic response, bandwidth, timing, multiple triggering functions, and input resistance.

Please Visit Product Demo Intro Video

Megohm meters. This option sources high ohms, high voltage resistors up to 18 G ohms. It also measures high voltage outputs.

Protective circuits prevent damage

Mains voltage inadvertently applied to a calibrator’s output terminals can cause extensive damage, requiring costly repairs. Electrical protection for calibrator outputs is vital for daily operation. The 5080A calibrator’s innovative protection circuitry prevents it from being damaged by reversed input voltage, so you can use it with confidence day after day.

Highest voltage and current compliance

The 5080A has the highest voltage and current compliance of any calibrator in the Fluke Calibration multi-product and multifunction calibrator families, making it an ideal solution for calibrating analog meters and other instruments requiring higher drive capability for proper operation.

For More Contact Details Please Visit:

R and S NGP800 Power supply series

R&S NGP800 Power supply series

The R&S®NGP800 DC power supply series, comprising five models with 400 W or 800 W, provides maximum power at a variety of operating points. The two or four 200 W outputs can each supply up to 64 V or up to 20 A. Electrically equivalent and galvanically isolated outputs can be wired in series or parallel for up to 250 V or 80 A.

Product Over View Demo Video

Five Models:

- NGP802: 2-CH | 400W | 2 x 32V/20A
- NGP804: 4-CH | 800W | 4 x 32V/20A
- NGP814: 4-CH | 800W | 2 x 32V/20A | 2 x 64V/10A
- NGP822: 2-CH | 400W | 2 x 64V/10A
- NGP824: 4-CH | 800W | 4 x 64V/10A

                                                                              

R&S®SMC100A Signal Generator

R&S®SMC100A Signal Generator

The analog R&S®SMC100A Signal Generator sets standards for attractively-priced signal generators. It has the smallest size and the best price/performance ratio in its class.

 

The flexible and versatile instrument is suited for use in service and maintenance labs. Due to its small dimensions and lightweight design, the R&S®SMC100A is also the perfect choice for field applications or training and education environments.

Key facts:

 

- Frequency range 9 kHz to 1.1 GHz or 3.2 GHz

- Maximum output level of typ. > +17 dBm

- Optional high-stability reference oscillator

- Analog modulation modes (AM/FM/φM/pulse) integrated as standard

- Integrated overvoltage protection

- Wear-free electronic attenuator

- Minimized total cost of ownership